Deckorators Aluminum 8 Railing Manuel d'utilisateur télécharger pdf

Prior to construction, check with your local regulatory agency for special code

requirements in your area. Common railing height is 36" or 42". Structural support

should come from either the continuation of deck support posts that extend up through

the deck ﬂoor or railing posts that are bolted to the inside of the rim or outer joists.

Never span more than 8' on-center between railing posts. Install railing posts before

deck boards are fastened to the joists. Pre-drilling of all railing components is essential

to successful installation. Work area should be kept clean of debris, including metal

shavings that can cause scratching. Do not over-tighten screws. Read instructions

completely to get an understanding of how the product goes together and how each

piece affects the other.

Step 1 Determine the number of railing posts needed for your deck. Post spacing is 8'

on-center. Example: A 16x20 deck attached to a building with a 4' access opening on

one side will require a total of eight posts (Figure 2).

Step 2 Install rail posts prior to installing deck boards. Cedar or pressure-treated pine

4x4 railing posts provide the structural strength for the railing. The length of each

structural post is determined by the total of the joist width (7-1/4") + decking thickness

(1") + railing height (36" or 42")=44-1/4" or 50-1/4".

Important: Do not notch the 4x4 railing posts (Figure 3a). Notching will reduce the

strength of the post and could result in railing collapse or failure.

Step 3 Position, plumb with a level, and clamp the rail post on the interior face of the

joist. Plumb again. The 4x4 railing post should be bolted to the inside of the joists using

two 1/2"x6" galvanized carriage bolts. Corner posts use a third carriage bolt inserted

through the adjacent joist (Figure 3b).

Step 4 Install decking; notch deck boards to ﬁt around the 4x4 railing posts.

8' Railing Installation

Instructions

For each 8' on-center

railing section, you will need:

One 8' Railing kit that contains:

• 2 rails

• 1 in-line hardware kit that contains:

4 in-line brackets

8 – #6 x 2" long #2 square head screws

12 – #4 x 1" long #2 square head screws

• 1 support block kit that contains:

1 support block

2 connectors

2 screws

One cap rail kit (optional) that contains:

• 1 cap rail

• 1 insert rail

• 9 – #4 x 1" long #2 square head screws

22.5˚ and 45˚ adaptor wedges are

available for angled railing applications.

Baluster Options

Classic, Estate, Twist or Ellipse baluster

kits that each contain:

• 10 aluminum balusters

• 20 balusters needed per 8' on-center

railing section (Classic, Estate and Twist)

• 24 balusters needed per 8' on-center

railing section (Ellipse)

Baluster connector or designer baluster

connector kits that each contain:

• 20 baluster connectors

• 1 kit needed per 10 balusters

Traditional baluster kit that contains:

• 10 aluminum balusters

• 40 color-matched, stainless steel screws

• 20 balusters needed per 8' on-center

railing section

Baroque or Arc baluster kits that each

contain:

• 5 aluminum balusters

• 20 color-matched, stainless steel screws

• 20 balusters needed per 8' on-center

railing section

Glass

• 5 glass balusters

• 20 stainless steel screws

• 12 balusters required per 8'

on-center railing section

One post sleeve

One post cap for each post sleeve

(sold separately)

One post base trim for each

post sleeve (sold separately)

Stair rail bracket kits for stair

railing sections. Two kits required

per 8' on-center railing section.

Each kit contains:

• 2 stair brackets

• 4 – #6 x 2" long

#2 square head screws

• 8 – #4 x 1" long

#2 square head screws

Stair baluster connectors kits that

each contain (Classic, Estate, Twist and

Ellipse only):

• 20 stair baluster connectors

• 1 kit needed per 10 balusters

Items you will need

• Drill/power screwdriver

• Miter or circular saw with

carbide-tipped blade

• Adjustable wrench or socket

wrench for bolts, etc.

• Assorted fasteners (see instructions)

• Tape measure

• Hammer

• Marked speed square

• Carpenter’s level

• Carpenter’s pencil

• Safety glasses/goggles

• Two clamps

• Hack saw

• Exterior-grade metal

construction adhesive

Cap Rail

Insert Rail

Support

Block

In-Line

Bracket (4)

Figure 1

Figure 2

Figure 3a

Fig.3.eps

Figure 3b

In-Line Railing Installation Instructions

Scan code to get more

information about installing

Deckorators Alumimum Railing.

Get the free mobile app at

http://gett ag.mobi

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Fig.3.eps

Prior to construction, check with your local regulatory agency for special code requirements in your area. Common railing height is 36" or 42&qu

Page 2

Paso 4 Instale la terraza; corte agujeros o muescas en las tablas de la terraza para ajustarlas alrededor de los postes de barandal de 4x4.Paso 5 Reco

Page 3 - Top View

Cobertura para posteSoporte en línea (4)Barandal de topeBarandal de inserción Bloque de apoyoParte exterior del porche/la terrazaBarandal superior e i

Page 4 - Bottom Rail

Soporte para escalera (4)Borde exterior de la escaleraTope para posteCobertura para posteBalaustre Menos de 6" Menos de 4" Barandal superior

Page 5

Step 5 Trim 4x4 post sleeves to length. Post sleeves should be a minimum of 1-1/2" longer than the overall railing height (Figure 4a and 4b). All

Page 6

Cap RailInsert Rail To p RailClassic, Estate, Twist and Ellipse balusters; and Glass balusters using connectors: Attach balusters to the lower rail b

Page 7 - Vue du haut

Stair Bracket (4)Figure 10Step 4 Measure the distance between installed post sleeves to determine the length of the top and bottom rails. Lay bottom r

Page 8 - Figure 9

Avant la construction, consultez l’agence réglementaire locale pour toutes exigences spéciales du code dans votre région. La hauteur courante de trave

Page 9

Étape 5 : Taillez les manchons de poteaux 4x4 pour la longueur. Les manchons de poteaux devraient être d’un moins 1 1/2 po plus longs que la hauteur d

Page 10

Balustres Classique, Estate, Twist et Ellipse; et balustres en verre utilisant des raccords :Attachez les balustres à la traverse inférieure en gliss

Page 11 - Vista superior

Fixation de marche (4)Bord extérieur des marchesChapeau de poteauManchon de poteauBalustreMoins de 6 poMoins de 4 poTraverse du haut et du basFigure 1

Page 12

Antes de iniciar la construcción, consulte en la correspondiente agencia local sobre la normativa y/o reglamentación especial que sea de aplicación en

Commentaires sur ces manuels

Pas de commentaire

Deckorators Aluminum 8 Railing Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Deckorators Aluminum 8 Railing. Deckorators Aluminum 8 Railing User Manual [en] [ru] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Deckorators Aluminum 8 Railing